产品信息查询
产品 技术 新闻 资料
首页 > 产品中心 > LED驱动电路 > LED路灯草坪灯车灯台灯闪灯射灯照明驱动IC > 升压型LED射灯驱动IC >CXLE8856 DC转换器可调节的输出电流内部智能模块自动调节连接在反馈引脚FB和接地之间的外部电流感测电阻器Rs进行编程驱动双电池碱性电池的高达1A的负载
CXLE8856 DC转换器可调节的输出电流内部智能模块自动调节连接在反馈引脚FB和接地之间的外部电流感测电阻器Rs进行编程驱动双电池碱性电池的高达1A的负载
17

CXLE8856是一个设置的DC-DC转换器,提供可调节的输出电流。设备以1.0兆赫的恒定频率切换,允许使用小值外部电感和陶瓷电容器。CXLE8856用于驱动双电池碱性电池的高达1A的负载。LED电流可由内部智能模块自动调节,并由连接在反馈引脚(FB)和接地之间的外部电流感测电阻器Rs进行编程。低95mV(典型值)反馈电压降低功率为提高效率而损失卢比。该装置内置2A、100mΩNMOS开关,即使在重载情况下也能提供高效率。在停机期间模式下,反馈电阻器Rs和负载完全断开,电流消耗降低到1uA
LED功率效率:高达90%
电流精度:5%
低启动电压:0.9V
低保持电压:0.75V
1MHz开关频率
使用小型、低调的外部组件

CXLE8856 DC转换器可调节的输出电流内部智能模块自动调节连接在反馈引脚FB和接地之间的外部电流感测电阻器Rs进行编程驱动双电池碱性电池的高达1A的负载
产品手册
样品申请

样品申请

产品简介

目录vbu嘉泰姆

1.产品概述                       2.产品特点vbu嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 vbu嘉泰姆
5.产品封装图                     6.电路原理图                   vbu嘉泰姆
7.功能概述                        8.相关产品
vbu嘉泰姆

一,产品概述(General Description)    vbu嘉泰姆


   The CXLE8856 is a set-up DC-DC converter that delivers a regulated output current. The device switches at a 1.0MHz constant frequency, allowing for thevbu嘉泰姆
use of small value external inductor and ceramic capacitors.The CXLE8856 is targeted to be used for driving loads up to 1A from a two-cell alkaline battery.vbu嘉泰姆
    The LED current can be auto adjusted by internal smart module and programmed by the external current sense resistor, Rs,connected between the feedback pin (FB) and ground. A low 95mV(TYP.) feedback voltage reduces the powervbu嘉泰姆
loss in the Rs for better efficiency. With its internal 2A,100mΩ NMOS switch, the device can provide high efficiency even at heavy load. During the shutdownvbu嘉泰姆
mode, the feedback resistor Rs and the load are completely disconnected and the current consumption is reduced to 1uA.The CXLE8856 is available in the 6-leadvbu嘉泰姆
SOT-23-6L package.vbu嘉泰姆
二.产品特点(Features)
vbu嘉泰姆


LED Power Efficiency: up to 90%vbu嘉泰姆
Current Accuracy: 5%(Vin =3.6V to 1.8Vvbu嘉泰姆
@Vf =3.7V)vbu嘉泰姆
Low Start-Up Voltage: 0.9Vvbu嘉泰姆
Low Hold Voltage:0.75Vvbu嘉泰姆
1MHz Switching Frequencyvbu嘉泰姆
Uses small, Low Profile External Componentsvbu嘉泰姆
Low RDS(ON) : 100mΩ (TYP.)vbu嘉泰姆
Over Temperature Protectionvbu嘉泰姆
Low Profile SOT-23-6L Packagevbu嘉泰姆
三,应用范围 (Applications)
vbu嘉泰姆


White LED Torch (Flashlight)vbu嘉泰姆
White LED Camera Flashvbu嘉泰姆
DSC(Digital Still Camera)Flashvbu嘉泰姆
Cellular Camera Phone Flashvbu嘉泰姆
PDA Camera Flashvbu嘉泰姆
Camcorder Torch(Flashlight) Lampvbu嘉泰姆
四.下载产品资料PDF文档 
vbu嘉泰姆


需要详细的PDF规格书请扫一扫微信联系我们,还可以获得免费样品以及技术支持vbu嘉泰姆

 QQ截图20160419174301.jpgvbu嘉泰姆

五,产品封装图 (Package)vbu嘉泰姆


image.pngvbu嘉泰姆

Pin No.vbu嘉泰姆

Pin Namevbu嘉泰姆

Pin Functionvbu嘉泰姆

1vbu嘉泰姆

SWvbu嘉泰姆

Switching Pin.vbu嘉泰姆

2vbu嘉泰姆

GNDvbu嘉泰姆

Ground Pin.vbu嘉泰姆

3vbu嘉泰姆

FBvbu嘉泰姆

Feedback Pin.vbu嘉泰姆

4vbu嘉泰姆

ENvbu嘉泰姆

Chip Enable(Active High).vbu嘉泰姆

5vbu嘉泰姆

VOUTvbu嘉泰姆

Output Voltage Pin.vbu嘉泰姆

6vbu嘉泰姆

VINvbu嘉泰姆

Input Supply.vbu嘉泰姆

六.电路原理图vbu嘉泰姆


image.pngvbu嘉泰姆
七,功能概述vbu嘉泰姆


Inductor Selectionvbu嘉泰姆
The CXLE8856 can use small value inductors due to its switching frequency of 1MHz. The value of inductor will focus in the range of 2.2uH to 4.7uH for most CXLE8856 applications. In typical high current white LED applications,it is recommended to use a 4.7uH inductor. The inductor should have low DCR (DC resistance) to minimize the IR power loss, and it requires a current rating of 2A to handle the peak inductor current without saturating. vbu嘉泰姆
Capacitor Selectionvbu嘉泰姆
An input capacitor is required to reduce the input ripple and noise for proper operation of the CXLE8856. For good input decoupling,  Low  ESR(equivalent  series  resistance) capacitors should be used at the input. At least 2.2uF input capacitor  is  recommended  for  most  applications. A minimum output capacitor value of 6.8uF is recommended under normal operating conditions, while a 10uF-22uF capacitor may be required for higher power LED current. A reasonable value of the output capacitor depends on the LED current. The ESR of the output capacitor is the important parameter to determine the output voltage ripple of the converter, so low ESR capacitors should be used at the output to reduce the output voltage ripple. The small size of ceramic capacitors is an excellent choice for CXLE8856 applications. The X5R and X7R types are preferred because they maintain capacitance over wide voltage and temperature ranges.vbu嘉泰姆
Diode Selectionvbu嘉泰姆
It's indispensable to use a Schottky diode rated at 2A with the CXLE8856. Using a Schottky diode with a lower forward voltage drop is better to improve the power LED efficiency, and its voltage rating should be greater than the output voltage. In application, the ON Semiconductor MBRA210LT3G is recommended. vbu嘉泰姆
LED Current Settingvbu嘉泰姆
The LED current is set by the single external Rs resistor connected to the FB pin as shown in the typical application circuit on page 1. The typical FB reference is internally regulated to 95mV(TYP.). The LED current is 95mV/Rs. It's recommended to use a 1% or better precision resistor for the better LED current accuracy.vbu嘉泰姆
The formula and table 1 for Rs selection are shown as follows:vbu嘉泰姆
Rs=95mV/ILEDvbu嘉泰姆
PCB Layout Guidelinesvbu嘉泰姆
For best performance of the CXLE8856, the following guidelines must be strictly followed. Input and Output capacitors should be placed close to the IC and connected to ground plane to reduce noise coupling.Keep the main current traces as possible as short and wide.SW node of DC-DC converter is with high frequency voltage swing. It should be kept at a small area.Place the feedback components as close as possible to the IC and keep away from the noisy devices.vbu嘉泰姆
八,相关产品                  更多同类产品.......
vbu嘉泰姆


升压型LED射灯驱动ICvbu嘉泰姆

型号vbu嘉泰姆

工作电压范围vbu嘉泰姆

输出电流vbu嘉泰姆

输出电流精度vbu嘉泰姆

效率vbu嘉泰姆

工作频率vbu嘉泰姆

调光功能vbu嘉泰姆

封装 vbu嘉泰姆

CXLE8856vbu嘉泰姆

0.9V-6.0Vvbu嘉泰姆

1Avbu嘉泰姆

-vbu嘉泰姆

90%vbu嘉泰姆

1.0 MHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOT-26vbu嘉泰姆

CXLE8857Bvbu嘉泰姆

0.8V-5.5Vvbu嘉泰姆

外置MOS/15Wvbu嘉泰姆

3%vbu嘉泰姆

90%vbu嘉泰姆

700KHzvbu嘉泰姆

PWM调光500Hz-1KHzvbu嘉泰姆

SOT-26vbu嘉泰姆

CXLE8858vbu嘉泰姆

3V-24Vvbu嘉泰姆

内置2A MOSvbu嘉泰姆

2%vbu嘉泰姆

90%vbu嘉泰姆

1.2MHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOT-26vbu嘉泰姆

CXLE8858Bvbu嘉泰姆

2.7V-6.5Vvbu嘉泰姆

内置2.8A MOSvbu嘉泰姆

2%vbu嘉泰姆

90%vbu嘉泰姆

1MHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOT-26vbu嘉泰姆

CXLE8859vbu嘉泰姆

2.5V-30Vvbu嘉泰姆

内置3A MOSvbu嘉泰姆

2%vbu嘉泰姆

90%vbu嘉泰姆

460KHzvbu嘉泰姆

模拟调光/PWM调光vbu嘉泰姆

SOP-8vbu嘉泰姆

CXLE8860vbu嘉泰姆

2.2V-6Vvbu嘉泰姆

内置3A MOSvbu嘉泰姆

2%vbu嘉泰姆

90%vbu嘉泰姆

800KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOP-8vbu嘉泰姆

CXLE8861vbu嘉泰姆

2.2V-6Vvbu嘉泰姆

内置3A MOSvbu嘉泰姆

2%vbu嘉泰姆

90%vbu嘉泰姆

800KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

DFN3*3-8vbu嘉泰姆

CXLE8862vbu嘉泰姆

10V-35Vvbu嘉泰姆

内置3A MOSvbu嘉泰姆

2%vbu嘉泰姆

90%vbu嘉泰姆

800KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOP-8vbu嘉泰姆

CXLE8863vbu嘉泰姆

4.5V--24Vvbu嘉泰姆

1Avbu嘉泰姆

2%vbu嘉泰姆

90%vbu嘉泰姆

800KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

ESOP8vbu嘉泰姆

CXLE8864vbu嘉泰姆

3.6V-26Vvbu嘉泰姆

2Avbu嘉泰姆

2%vbu嘉泰姆

92%vbu嘉泰姆

400KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOP-8vbu嘉泰姆

CXLE8865vbu嘉泰姆

3.6V-26Vvbu嘉泰姆

2Avbu嘉泰姆

2%vbu嘉泰姆

92%vbu嘉泰姆

400KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOP-8vbu嘉泰姆

CXLE8865Bvbu嘉泰姆

5V-45Vvbu嘉泰姆

2Avbu嘉泰姆

2%vbu嘉泰姆

93%vbu嘉泰姆

400KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOP-8vbu嘉泰姆

CXLE8866vbu嘉泰姆

8V-32Vvbu嘉泰姆

内置8A MOSvbu嘉泰姆

2%vbu嘉泰姆

92%vbu嘉泰姆

1MHzvbu嘉泰姆

PWM调光vbu嘉泰姆

SOP-14vbu嘉泰姆

CXLE8867vbu嘉泰姆

8V-32Vvbu嘉泰姆

外置MOS/36Wvbu嘉泰姆

2%vbu嘉泰姆

94%vbu嘉泰姆

1MHzvbu嘉泰姆

PWM调光vbu嘉泰姆

ESOP-8vbu嘉泰姆

CXLE8868vbu嘉泰姆

3.6V-36Vvbu嘉泰姆

4Avbu嘉泰姆

2%vbu嘉泰姆

94%vbu嘉泰姆

180KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

TO252-5Lvbu嘉泰姆

CXLE8869vbu嘉泰姆

5.0V-36Vvbu嘉泰姆

5Avbu嘉泰姆

2%vbu嘉泰姆

94%vbu嘉泰姆

180KHzvbu嘉泰姆

PWM调光vbu嘉泰姆

TO-263-5Lvbu嘉泰姆

发表评论
    共有条评论
    用户名: 密码:
    验证码: 匿名发表

热门信息
  • 最新信息
    推荐信息
    相关文章
  • CXLE87108高稳定性的太阳能蜡灯控制芯片输入电流可蜡
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • CXLE86148单通道高压线性恒流LED驱动芯片针对小功率LE
  • 推荐资讯
    智能电表驱动技术全景解析:从计量芯片到通信模块的完整指南
    智能电表驱动技术全景
    电子秤显示模块核心技术解析:从LCD驱动到智能接口的全方案指南
    电子秤显示模块核心技
    显示驱动电路深度解析:从基础原理到先进设计的完整指南  SEO关键词:
    显示驱动电路深度解析
    智能家电控制系统全面解析:从技术原理到未来趋势的深度指南
    智能家电控制系统全面
    串行通信接口终极指南:从基础原理到高速协议的全景解析
    串行通信接口终极指南
    家电显示控制系统全景解读:从UI设计到智能交互的技术演进
    家电显示控制系统全景
    辉度调节技术全面解析:从PWM调光到智能亮度控制的全景指南
    辉度调节技术全面解析
    串行接口终极指南:从UART到PCIe,详解串行通信原理与应用
    串行接口终极指南:从UA
    显示控制系统深度解析:从驱动原理到多屏交互的全景指南
    显示控制系统深度解析
    段码LED显示技术详解:原理、应用与选型指南
    段码LED显示技术详解:
    键盘扫描揭秘:从原理到应用,全面解析键盘如何识键如神
    键盘扫描揭秘:从原理到
    恒流驱动:终极指南 - 原理、优势与应用场景
    恒流驱动:终极指南 -