CXLE8945 CXLE8946用于驱动小于60V的LED串，通过VC与GND之间的电容器消除交直流电源上的100/120Hz电流纹波。CXLE8945允许用户通过在VLMT和GND之间连接一个电阻器来设置LED管脚上的最大电压。如果LED管脚上的电压超过极限阈值，则电流纹波消除器将被禁用并保持LED电压，这有助于限制芯片上的功耗。多个JCXLE8945可以通过将所有VC管脚短接在一起并行工作。每个CXLE8945之间的平均电流匹配率小于±1%。最大LED电流内部限制为440毫安。CXLE8945提供热保护
可扩展自适应100/120Hz电流纹波消除器
5V~60V输入电压
内置LED驱动MOSFET
LED电压低至0.65V@0.25A
可编程LED电流纹波
可编程最大LED电压
过热保护
-
[ CXLE8945 ]
目录
7.相关产品
产品概述 返回TOP
CXLE8945 CXLE8946 is used to drive a LED string (＜60V), and remove the 100/120Hz current ripple on AC/DC power by a capacitor between VC and GND. CXLE8945 allows user to setup the maximum voltage on LED pin by connect a resistor between VLMT and GND. If the voltage on LED pin exceeds limit threshold, the current ripple remover is disabled and remain the LED voltage, which could help limiting the power dissipation on chip. Multiple JCXLE8945 can operate in parallel by shorting all VC PINs together. The average current matching rate between each CXLE8945 is less than ±1%. The maximum LED current is internally limited as 440mA. CXLE8945provides thermal protection
产品特点 返回TOP
Scalable Adaptive 100/120Hz Current Ripple
Remover
5V~60V Input Voltage
Built-in LED Driving MOSFET
LED Voltage Low to 0.65V @ 0.25A
Programmable LED Current Ripple
Programmable maximum LED Voltage
Over thermal protection
eSOP8 and TO220-5L package
应用范围 返回TOP
LED Lighting
技术规格书（产品PDF) 返回TOP要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！
产品封装图 返回TOP
电路原理图 返回TOP
相关芯片选择指南 返回TOP
|
工频纹波滤除产品 |
||||||
|
产品型号 |
描述 |
LED 电压 |
最大输出电流(A) |
功率管 |
封装 |
OCP,OVP,和OTP |
|
自适应100/120Hz 电流纹波消除IC |
4.5 - 60 |
0.35 |
内置 |
ESOP8 TO220-5 |
Latch-off |
|
|
自适应100/120Hz 电流纹波消除IC(适用于Triac 调光) |
5 - 60 |
0.6 |
内置 |
ESOP8 |
Hiccup |
|
|
自适应100/120Hz 电流纹波消除IC |
10 - 60 |
1 |
内置 |
TO252-5 |
Hiccup |
|
|
自适应100/120Hz 电流纹波消除IC |
10 - 60 |
0.5 |
内置 |
ESOP8 |
Hiccup |
|
|
集成高压MOS的自适应100/120Hz电流纹波消除IC |
12-130 |
0.5 |
内置 |
ESOP8 |
Hiccup |
|
|
自适应100/120Hz 电流纹波消除控制器 |
Up to 200V |
Up to 5A |
外置 |
SOT23-6 |
Hiccup |
|
| 头条信息 |
|---|
