目录xRj嘉泰姆

1.产品概述                       2.产品特点xRj嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 xRj嘉泰姆
5.产品封装图                     6.电路原理图                   xRj嘉泰姆
7.功能概述                        8.相关产品xRj嘉泰姆

一,产品概述(General Description)  xRj嘉泰姆

    The CXSD62121A CXSD62121B CXSD62121 integrates a synchronous buck PWM con-troller to generate VDDQ, a sourcing and sinking LDO linear regulator to generate VTT. It offers the lowest total solution cost in system where space is at a premium.  The CXSD62121A CXSD62121B CXSD62121 provides excellent transient response and accurate DC voltage output in either PFM or PWM Mode.In Pulse Frequency Mode (PFM), the CXSD62121A CXSD62121B CXSD62121 provides very high efficiency over light to heavy loads with loading-modulated switching frequencies. On TQFN-20 Package,the Forced PWM Mode works nearly at constant frequency for low-noise requirements.  The CXSD62121A CXSD62121B CXSD62121 is equipped with accurate current-limit,output under-voltage, and output over-voltage protections.A Power-On- Reset function monitors the voltage on VCC prevents wrong operation during power on. Droop func-tion is allowed to adjust output voltage during light load period.The LDO is designed to provide a regulated voltage with bi-directional output current for DDR-SDRAM termination.The device integrates two power transistors to source or sink current up to 1.5A. It also incorporates current-limit and thermal shutdown protection.The output voltage of LDO tracks the voltage at VREF pin.An internal resistor divider is used to provide a half volt-age of VREF for VTTREF and VTT Voltage. The VTT output voltage is only requiring 20μF of ceramic output capaci tance for stability and fast transient response. The S3 and S5 pins provide the sleep state for VTT (S3 state)and suspend state (S4/S5 state) for device, when S5 and S3 are both pulled low the device provides the soft-off for VTT and VTTREF                                                         xRj嘉泰姆

产品特点(Features)xRj嘉泰姆

High Input Voltages Range from 3V to 28V Input PowerxRj嘉泰姆
Provide Adjustable Output Voltage from 0.75V toxRj嘉泰姆
5.5V +1% Accuracy over TemperaturexRj嘉泰姆
Integrated MOSFET Drivers and Bootstrap Forward P-CH MOSFETxRj嘉泰姆
Low Quiescent Current (200μA)xRj嘉泰姆
Excellent Line and Load Transient ResponsesxRj嘉泰姆
PFM Mode for Increased Light Load EfficiencyxRj嘉泰姆
Constant On-Time Controller SchemexRj嘉泰姆
- Switching Frequency Compensation for PWM ModexRj嘉泰姆
- Adjustable Switching Frequency from 100kHz toxRj嘉泰姆
550kHz in PWM Mode with DC Output CurrentxRj嘉泰姆
S3 and S5 Pins Control The Device in S0, S3 or S4/S5 StatexRj嘉泰姆
Power Good MonitoringxRj嘉泰姆
Extra Droop Voltage Control Function withxRj嘉泰姆
Adjustable Current SettingxRj嘉泰姆
70% Under-Voltage Protection (UVP)xRj嘉泰姆
125% Over-Voltage Protection (OVP)xRj嘉泰姆
Adjustable Current-Limit ProtectionxRj嘉泰姆
- Using Sense Low-Side MOSFET’s RDS(ON)xRj嘉泰姆
TQFN-20 3mmx3mm Thin packagexRj嘉泰姆
Lead Free Available (RoHS Compliant)xRj嘉泰姆
+1.5A LDO Section (VTT)xRj嘉泰姆
Sourcing or Sinking Current up to 1.5AxRj嘉泰姆
Fast Transient Response for Output VoltagexRj嘉泰姆
Output Ceramic Capacitors Support at least 10μF MLCCxRj嘉泰姆
VTT and VTTREF Track at Half the VDDQSNS by internal dividerxRj嘉泰姆
+20mV Accuracy for VTT and VTTREFxRj嘉泰姆
Independent Over-Current Limit (OCL)xRj嘉泰姆
Thermal Shutdown ProtectionxRj嘉泰姆
三,应用范围 (Applications)xRj嘉泰姆

DDR2, and DDR3 Memory Power SuppliesxRj嘉泰姆
SSTL-2 SSTL-18 and HSTL TerminationxRj嘉泰姆
四.下载产品资料PDF文档 xRj嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！xRj嘉泰姆

 xRj嘉泰姆

五,产品封装图 (Package)xRj嘉泰姆

xRj嘉泰姆
六.电路原理图xRj嘉泰姆

xRj嘉泰姆

七,功能概述xRj嘉泰姆

Soft- Start (cont.)xRj嘉泰姆

During soft-start stage before the PGOOD pin is ready,xRj嘉泰姆
the under voltage protection is prohibited. The over volt-xRj嘉泰姆
age and current limit protection functions are enabled. IfxRj嘉泰姆
the output capacitor has residue voltage before startup,xRj嘉泰姆
both low-side and high-side MOSFETs are in off-statexRj嘉泰姆
until the internal digital soft start voltage equal the inter-xRj嘉泰姆
nal feedback voltage. This will ensure the output voltagexRj嘉泰姆
starts from its existing voltage level.xRj嘉泰姆
The VTT LDO part monitors the output current, both sourc-xRj嘉泰姆
ing and sinking current, and limits the maximum outputxRj嘉泰姆
current to prevent damages during current overload orxRj嘉泰姆
short circuit (shorted from VTT to GND or VLDOIN)xRj嘉泰姆
conditions.xRj嘉泰姆
The VTT LDO provides a soft-start function, using thexRj嘉泰姆
constant current to charge the output capacitor that givesxRj嘉泰姆
a rapid and linear output voltage rise. If the load current isxRj嘉泰姆
above the current limit start-up, the VTT cannot startxRj嘉泰姆
successfully.CXSD62121A CXSD62121B CXSD62121 has an independent counter for each output,xRj嘉泰姆
but the PGOOD signal indicates only the status of VDDQxRj嘉泰姆
and does not indicate VTT power good externally.xRj嘉泰姆
Power-Good Output (PGOOD)xRj嘉泰姆
PGOOD is an open-drain output and the PGOOD com-xRj嘉泰姆
parator continuously monitors the output voltage. PGOODxRj嘉泰姆
is actively held low in shutdown, and standby. When PWMxRj嘉泰姆
converter’s output voltage is greater than 95% of its tar-xRj嘉泰姆
get value, the internal open-drain device will be pulledxRj嘉泰姆
low. After 63μs debounce time, the PGOOD goes high.xRj嘉泰姆
The PGOOD goes low if VVDDQ output is 10% below orxRj嘉泰姆
above its nominal regulation point.xRj嘉泰姆
Under Voltage ProtectionxRj嘉泰姆
In the process of operation, if a short-circuit occurs, thexRj嘉泰姆
output voltage will drop quickly. When load current is big-xRj嘉泰姆
ger than current limit threshold value, the output voltagexRj嘉泰姆
will fall out of the required regulation range. The under-xRj嘉泰姆
voltage continually monitors the setting output voltagexRj嘉泰姆
after 2ms of PWM operations to ensure startup. If a loadxRj嘉泰姆
step is strong enough to pull the output voltage lowerxRj嘉泰姆
than the under voltage threshold (70% of normal outputxRj嘉泰姆
voltage), CXSD62121A CXSD62121B CXSD62121 shuts down the output gradually andxRj嘉泰姆
latches off both high and low side MOSFETs.xRj嘉泰姆
Over Voltage Protection (OVP)xRj嘉泰姆
The feedback voltage should increase over 125% of thexRj嘉泰姆
reference voltage due to the high-side MOSFET failure orxRj嘉泰姆
for other reasons, and the over voltage protection com-xRj嘉泰姆
parator designed with a 1.5μs noise filter will force thexRj嘉泰姆
low-side MOSFET gate driver to be high. This action ac-xRj嘉泰姆
tively pulls down the output voltage and eventually at-xRj嘉泰姆
tempts to blow the battery fuse.xRj嘉泰姆
When the OVP occurs, the PGOOD pin will pull down andxRj嘉泰姆
latch-off the converter. This OVP scheme only clamps thexRj嘉泰姆
voltage overshoot, and does not invert the output voltagexRj嘉泰姆
when otherwise activated with a continuously high outputxRj嘉泰姆
from low-side MOSFET driver. It’s a common problem forxRj嘉泰姆
OVP schemes with a latch. Once an over-voltage faultxRj嘉泰姆
condition is set, toggling VCC power-on-reset signal canxRj嘉泰姆
only reset it.xRj嘉泰姆
PWM Converter Current LimitxRj嘉泰姆
The current-limit circuit employs a unique “valley” currentxRj嘉泰姆
sensing algorithm (Figure 2). CS pin should be con-xRj嘉泰姆
nected to VCC through the trip voltage-setting resistor,xRj嘉泰姆
RCS. CS terminal sinks 5mA current, ICS, and the currentxRj嘉泰姆
limit threshold is set to the voltage across the RCS. ThexRj嘉泰姆
voltage between or CS_GND pin and PHASE pin moni-xRj嘉泰姆
tors the inductor current so that PHASE pin should bexRj嘉泰姆
connected to the drain terminal of the low side MOSFET.xRj嘉泰姆
PGND is used as the positive current sensing node soxRj嘉泰姆
that PGND should be connected to the proper currentxRj嘉泰姆
sensing device, i.e. the sense resistor or the source ter-xRj嘉泰姆
minal of the low side MOSFET.xRj嘉泰姆
If the magnitude of the current-sense signal is above thexRj嘉泰姆
current-limit threshold, the PWM is not allowed to initiatexRj嘉泰姆
a new cycle. The actual peak current is greater than thexRj嘉泰姆
current-limit threshold by an amount equal to the induc-xRj嘉泰姆
tor ripple current. Therefore, the exact current- limit char-xRj嘉泰姆
acteristic and maximum load capability are a function ofxRj嘉泰姆
the sense resistance, inductor value, and input voltage.xRj嘉泰姆
八,相关产品               更多同类产品...... xRj嘉泰姆

共有条评论 用户名: 密码: 验证码: 匿名发表