CXSD62130A 1A输出电流宽电压2.7V~6.0V输入固定1.5MHz开关频率100%占空比同步整流器

目录HSh嘉泰姆

1.产品概述                       2.产品特点HSh嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 HSh嘉泰姆
5.产品封装图                     6.电路原理图                   HSh嘉泰姆
7.功能概述                        8.相关产品HSh嘉泰姆

一,产品概述(General Description)   HSh嘉泰姆

 CXSD62130 CXSD62130A is a 1.5MHz high efficiency monolithic synchronous buck regulator. Design with current mode scheme,the CXSD62130 CXSD62130A is stable HSh嘉泰姆

with ceramic output capacitor. Input voltage from 2.7V to 6.0V makes the HSh嘉泰姆

CXSD62130 CXSD62130A ideally suited for single Li-Ion battery powered HSh嘉泰姆

applications. 100%duty cycle provides low dropout operation, extending HSh嘉泰姆

battery life in portable electrical devices. Theinternally fixed 1.5MHz HSh嘉泰姆

operating frequency allows the using of small surface mount inductors and capacitors. The synchronous switches included inside increase the efficiencyHSh嘉泰姆

and eliminate the need of an external Schottky diode.HSh嘉泰姆
   The CXSD62130 CXSD62130A is available in TDFN2x2-6 packages.HSh嘉泰姆
二.产品特点(Features)HSh嘉泰姆

1A Output CurrentHSh嘉泰姆
Wide 2.7V~6.0V Input VoltageHSh嘉泰姆
Fixed 1.5MHz Switching FrequencyHSh嘉泰姆
Low Dropout Operating at 100% Duty CycleHSh嘉泰姆
25μA Quiescent CurrentHSh嘉泰姆
Synchronous RectifierHSh嘉泰姆
0.6V Reference VoltageHSh嘉泰姆
<0.5μA Input Current During ShutdownHSh嘉泰姆
Short-Circuit ProtectionHSh嘉泰姆
Over-Temperature ProtectionHSh嘉泰姆
Available in TDFN2x2-6 PackagesHSh嘉泰姆
Lead Free and Green Devices AvailableHSh嘉泰姆
(RoHS Compliant)HSh嘉泰姆
三,应用范围 (Applications)HSh嘉泰姆

HD STBHSh嘉泰姆
BT MouseHSh嘉泰姆
PND InstrumentHSh嘉泰姆
Portable InstrumentHSh嘉泰姆
四.下载产品资料PDF文档 HSh嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！HSh嘉泰姆

 HSh嘉泰姆

五,产品封装图 (Package)HSh嘉泰姆

HSh嘉泰姆
六.电路原理图HSh嘉泰姆

HSh嘉泰姆
HSh嘉泰姆

七,功能概述HSh嘉泰姆

Main Control LoopHSh嘉泰姆
The CXSD62130 CXSD62130A is a constant frequency, synchronous rectifier and current-mode HSh嘉泰姆

switching regulato r. In normal operation, the internal P-channel power MOSFET is turned on eachHSh嘉泰姆

 cycle. The peak inductor current at which ICMP turn off the P-FET is controlled by the voltage onHSh嘉泰姆

 the COMP node, which is the output of the error amplifier (EAMP). An external resistive divider HSh嘉泰姆

connected between VOUT and ground allows the EAMP to receive an output feedback voltage HSh嘉泰姆

VFB at FB pin. When the load current increases, it causes a slightly decrease in VFB relative toHSh嘉泰姆

the 0.6V reference, which in turn causes the COMP voltage to increase until the average HSh嘉泰姆

inductor current matches the new load current.HSh嘉泰姆
Enable/ShutdownHSh嘉泰姆
Driving RUN to the ground places the CXSD62130 CXSD62130A in shutdown mode. WhenHSh嘉泰姆

 in shutdown, the internal power MOSFETs turn off, all internal circuitry shuts down and theHSh嘉泰姆

 quiescent supply current reduces to 0.5μA maximum.HSh嘉泰姆
Pulse Frequency Modulation Mode (PFM)HSh嘉泰姆
The CXSD62130 CXSD62130A is a fixed frequency, peak current mode PWM step-down HSh嘉泰姆

converter. At light loads, the CXSD62130 CXSD62130A will automatically enter in pulse HSh嘉泰姆

frequency mode operation to reduce the dominant switching losses. In PFM operation, HSh嘉泰姆

the inductor current may reach zero or reverse on each pulse. A zero current comparator HSh嘉泰姆

turn off the N-FET, forcing DCM operation at light load. These controls get very low HSh嘉泰姆

quiescent current, help to maintain high effi-ciency over the complete load range.HSh嘉泰姆
Slope Compensation and Inductor Peak CurrentHSh嘉泰姆
The CXSD62130 CXSD62130A is a peak current mode PWM step downconverter. ToHSh嘉泰姆

 prevent sub-harmonic oscillations, theCXSD62130 CXSD62130A sense the peak current and HSh嘉泰姆

add slope compensation to stable the converter. It is accomplished in-ternally by addingHSh嘉泰姆

a compensating ramp to the inductor current signal at duty cycles in excess of 40%.HSh嘉泰姆

 Normally,this results in a reduction of maximum inductor peak current for duty cycles >HSh嘉泰姆

 40%. However, the CXSD62130 CXSD62130A uses a special scheme that counteracts this HSh嘉泰姆

compensating ramp, which allows the maximum inductor peak current to remain unaffectedHSh嘉泰姆

 throughout all duty cycles.HSh嘉泰姆
Dropout OperationHSh嘉泰姆
As the input supply voltage decreases to a value ap-proaching the output voltage, the dutyHSh嘉泰姆

 cycle increases toward the maximum on time. Further, reduction of thesupply voltage forces HSh嘉泰姆

the main switch to remain on for more than one cycle until it reaches 100% duty cycle. TheHSh嘉泰姆

 input voltage minus the voltage drop will determine the output voltage across the P-FETHSh嘉泰姆

 and the inductor.An important detail to remember is that on resistance of P-FET switch HSh嘉泰姆

will increase at low input supply voltageTherefore, the user should calculate the power dissipa-HSh嘉泰姆
tion when the CXSD62130 CXSD62130A is used at 100% duty cycle with low input voltage.HSh嘉泰姆
Over-Temperature Protection (OTP)HSh嘉泰姆
The over-temperature circuit limits the junction tempera-ture of the CXSD62130 CXSD62130A. HSh嘉泰姆

When the junction temperature ex-ceeds 150oC, a thermal sensor turns off the both power HSh嘉泰姆

MOSFETs, allowing the devices to cool. The thermal sen-sor allows the converters to start a HSh嘉泰姆

soft-start process and regulate the output voltage again after the junction tem-perature coolsHSh嘉泰姆

 by 30oC. The OTP is designed with a 30oC hysteresis to lower the average JunctionHSh嘉泰姆

 Temperature (TJ) during continuous thermal overload conditions, in-creasing the lifetime HSh嘉泰姆

of the device.HSh嘉泰姆
八,相关产品                    更多同类产品.......HSh嘉泰姆